View HT82K68E07_1012789.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

HT82K68E
8-Bit Multimedia Keyboard Encoder OTP MCU
Features
* Operating voltage: 2.4V~5.5V * 32/34 bidirectional I/O lines * One 8-bit programmable timer counter with overflow * HALT function and wake-up feature reduce power
consumption
* Six-level subroutine nesting * Bit manipulation instructions * 16-bit table read instructions * 63 powerful instructions * All instructions in 1 or 2 machine cycles * 20/28-pin SOP, 40-pin DIP, 48-pin SSOP package
interrupts
* Crystal or RC oscillator * Watchdog Timer * 3K16 program EPROM * 1608 data RAM * One external interrupt pin (shared with PC2)
General Description
The HT82K68E is an 8-bit high performance peripheral interface IC, designed for multiple I/O products and multimedia applications. It supports interface to a low speed PC with multimedia keyboard or wireless keyboard in Windows 95, Windows 98 or Windows 2000 environment. A HALT feature is included to reduce power consumption.
Block Diagram
STACK0 STACK1 STACK2 STACK3 P ro g ra m ROM P ro g ra m C o u n te r STACK4 STACK5 PC2 In te rru p t C ir c u it IN T C TM R TM RC
S Y S C L K /4
8 b it S Y S C L K /4 W DT M U X RC OSC
In s tr u c tio n R e g is te r
MP0 MP1 M
U X
DATA M e m o ry
W DTS W D T P r e s c a le r
In s tr u c tio n D ecoder ALU T im in g G e n e ra to r
MUX
PEC PE STATUS PDC PD PCC PC
PORT E
PE0~PE4
PORT D
PD0~PD7
S h ifte r
PORT C
PC0~PC7
OSC2
OS RE VD VS S
C1 SET D
ACC
PBC PB PAC PA
PORT B
PB0~PB7
PORT A
PA0~PA7
Rev. 1.10
1
November 14, 2001
HT82K68E
Pin Assignment
PA3 PA2 PA1 PA0 PB1 PB0 VSS PE2 PC0 PC1 9 10 8 7 6 5 4 3 2 1 20 19 18 17 16 15 14 13 12 11 PA4 PA5 PA6 PA7 OSC2 OSC1 VDD RESET PC3 PC2 PB5 PB4 PA3 PA2 PA1 PA0 PB5 PB4 PA3 PA2 PA1 PA0 PB3 PB2 PB1 PB0 VSS PC1 PC2 PC3 9 10 11 12 13 14 8 7 6 5 4 3 2 1 28 27 26 25 24 23 22 21 20 19 18 17 16 15 PB6 PB7 PA4 PA5 PA6 PA7 OSC2 OSC1 VDD RESET PC7 PC6 PC5 PC4 PB3 PB2 PB1 PB0 PD7 PD6 PD5 PD4 VSS P E 2 (L E D ) P E 3 (L E D ) PC0 PC1 PC2 9 10 11 12 13 14 15 16 17 18 19 20 8 7 6 5 4 3 2 1 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 PB6 PB7 PA4 PA5 PA6 PA7 OSC2 OSC1 VDD RESET P E 4 (L E D ) PD3 PD2 PD1 PD0 PC7 PC6 PC5 PC4 PC3 PB5 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 PB4 PA3 PA2 PA1 PA0 PB3 PB2 PB1 PB0 NC NC PD7 PD6 PD5 PD4 VSS P E 2 (L E D ) P E 3 (L E D ) PC0 PC1 PC2 PE0 PE1 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 PB6 PB7 PA4 PA5 PA6 PA7 NC NC NC NC OSC2 OSC1 VDD RESET P E 4 (L E D ) PD3 PD2 PD1 PD0 PC7 PC6 PC5 PC4 PC3
H T82K 68E 2 0 S O P -A
H T82K 68E 2 8 S O P -A
H T82K 68E 4 0 D IP -A
H T82K 68E 4 8 S S O P -A
Pin Description
Pin Name I/O Mask Option Wake-up Pull-high or None Pull-high or None Wake-up Pull-high or None Wake-up Pull-high or None Wake-up Pull-high or None Pull-high or None Pull-high or None Description Bidirectional 8-bit input/output port. Each bit can be configured as a wake-up input by mask option. Software* instructions determine the CMOS output or Schmitt Trigger input with or without 12K pull-high resistor. Bidirectional 8-bit input/output port. Software* instructions determine the output or Schmitt Trigger input with or without pull-high resistor. This pin is an I/O port. NMOS open drain output with pull-high resistor and can be used as DATA or CLOCK line of PS2. This pin can be configured as a wake-up input by mask option. This pin is an I/O port. NMOS open drain output with pull-high resistor and can be used as DATA or CLOCK line of PS2. This pin can be configured as a wake-up input by mask option. Bidirectional 2-bit input/output port. Each bit can be configured as a wake-up input by mask option. Software* instructions determine the CMOS output or Schmitt Trigger input with or without pull-high resistor. PC2 also as external interrupt input pin. PE0 determine whether rising edge or falling edge of PC2 to trigger the INT circuit. Bidirectional 4-bit input/output port. Software* instructions determine the CMOS output or Schmitt Trigger input with or without pull-high resistor. Bidirectional 8-bit input/output port. Software* instructions determine the CMOS output or Schmitt Trigger input with or without pull-high resistor.
PA0~PA7
I/O
PB0~PB7
I/O
PC0
I/O
PC1
I/O
PC2~PC3
I/O
PC4~PC7 PD0~PD7
I/O I/O
Rev. 1.10
2
November 14, 2001
HT82K68E
Pin Name I/O Mask Option Pull-high or None Description Bidirectional input/output port. Software* instruction determine the CMOS output or Schmitt Trigger input with or without pull-high resistor. If PE0 output 1, rising edge of PC2 trigger INT circuit. PE0 output 0, falling edge of PC2 trigger INT circuit. This pin is a CMOS output structure. The pad can function as LED (SCR) drivers for the keyboard. IOL=14mA, @VOL=3.2V This pin is a CMOS output structure. The pad can function as LED (NUM) drivers for the keyboard. IOL=14mA, @VOL=3.2V This pin is a CMOS output structure. The pad can function as LED (CAP) drivers for the keyboard. IOL=14mA, @VOL=3.2V 3/4 3/4 3/4 Positive power supply Negative power supply, ground Chip reset input. Active low. Built-in power-on reset circuit to reset the entire chip. Chip can also be externally reset via RESET pin
PE0~PE1
I/O
PE2 PE3 PE4 VDD VSS RESET OSC1 OSC2 Note:
O O O 3/4 3/4 I I O
OSC1, OSC2 are connected to an RC network or a crystal for the internal system Crystal or RC clock. In the case of RC operation, OSC2 is the output terminal for the 1/4 system clock; A 110kW resistor is connected to OSC1 to generate a 2 MHZ frequency.
*: Software means the HT-IDE (Holtek Integrated Development Environment) can be configured by mask option.
Absolute Maximum Ratings
Supply Voltage ........................................-0.3V to 5.5V Input Voltage .............................VSS-0.3V to VDD+0.3V Storage Temperature ...........................-50C to 125C Operating Temperature ..........................-25C to 70C
Note: These are stress ratings only. Stresses exceeding the range specified under Absolute Maximum Ratings may cause substantial damage to the device. Functional operation of this device at other conditions beyond those listed in the specification is not implied and prolonged exposure to extreme conditions may affect device reliability.
D.C. Characteristics
Symbol VDD IDD1 Parameter Operating Voltage Operating Current (Crystal OSC) 5V 3V Operating Current (RC OSC) 5V 3V Standby Current (WDT enabled) 5V 3V Standby Current (WDT Disabled) 5V 3V Input Low Voltage for I/O Ports (Schmitt) 5V 3V Input High Voltage for I/O Ports (Schmitt) 5V 3/4 3/4 3/4 3/4 No load, system HALT No load, system HALT Test Conditions VDD 3/4 3V Conditions 3/4 No load, fSYS= 6MHz Min. 2.4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 0 0 2.1 3.5 Typ. 3/4 0.7 2 0.5 2 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 Max. 5.5 1.5 5 1 5 8 15 3 6 0.9 1.5 3 5
Ta=25C Unit V mA mA mA mA mA mA mA mA V V V V
IDD2
No load, fSYS= 6MHz
ISTB1
ISTB2
VIL1
Rev. 1.10
3
November 14, 2001
HT82K68E
Symbol Parameter Test Conditions VDD 3V Input Low Voltage for I/O Ports (CMOS) 5V 3V Input High Voltage for I/O Ports (CMOS) 5V 3V Input Low Voltage (RESET) 5V 3V Input High Voltage (RESET) 5V I/O Port Sink Current I/O Port Source Current LED Sink Current (SCR, NUM, CAP) Power-on Reset Time Internal Pull-high Resistance of PA, PB, PC, PD, PE Port Internal Pull-high Resistance of DATA, CLK Internal Pull-high Resistance of RESET Frequency Variation Frequency Variation 5V 5V 5V 5V 5V 5V 5V 5V 5V Crystal RC VOL= 0.5V VOH= 4.5V VOL=3.4V 3/4 3/4 3/4 3/4 Conditions 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 Min. 0 0 1.7 2.7 0 0 2.4 4.0 7 -2.5 10 120 5 2 15 3/4 3/4 Typ. 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 12 -4.5 14 150 12 4.7 31 3/4 3/4 Max. 1.2 2.3 3 5 0.7 1.3 3 5 3/4 3/4 18 180 20 8 46 1 10 Unit V V V V V V V V mA mA mA ms kW kW kW % %
VIL2
VIH2
VIL3
VIH3 IOL IOH ILED tPOR RPH RPH1 RPH2 Df/f Df/f1
A.C. Characteristics
Symbol Parameter Test Conditions VDD 3V System Clock (Crystal OSC) 5V 3V System Clock (RC OSC) 5V 3V Watchdog Oscillator 5V Watchdog Time-out Period (RC) Watchdog Time-out Period (System Clock) External Reset Low Pulse Width System Start-up Timer Period Interrupt Pulse Width tSYS= 1/fSYS 3V 5V 3/4 3/4 3/4 3/4 Conditions 3/4 3/4 3/4 3/4 3/4 3/4 Without WDT prescaler Without WDT prescaler 3/4 Power-up or wake-up from HALT 3/4 Min. 3/4 3/4 3/4 3/4 45 35 12 9 3/4 1 3/4 1 Typ. 6 6 6 6 90 76 23 19 1024 3/4 1024 3/4 Max. 3/4 3/4 3/4 3/4 180 130 45 35 3/4 3/4 3/4 3/4
Ta=25C Unit MHz MHz MHz MHz ms ms ms ms tSYS ms tSYS ms
fSYS1
fSYS2
tWDTOSC
tWDT1 tWDT2 tRES tSST tINT Note:
Rev. 1.10
4
November 14, 2001
HT82K68E
Functional Description
Execution flow The HT82K68E system clock is derived from either a crystal or an RC oscillator. The system clock is internally divided into four non-overlapping clocks. One instruction cycle consists of four system clock cycles. Instruction fetching and execution are pipelined in such a way that a fetch takes one instruction cycle while decoding and execution takes the next instruction cycle. However, the pipelining scheme causes each instruction to effectively execute within one cycle. If an instruction changes the program counter, two cycles are required to complete the instruction. Program counter - PC The 12-bit program counter (PC) controls the sequence in which the instructions stored in the program ROM are executed and its contents specify a maximum of 4096 addresses. After accessing a program memory word to fetch an instruction code, the contents of the program counter are incremented by one. The program counter then points to the memory word containing the next instruction code. When executing a jump instruction, conditional skip execution, loading PCL register, subroutine call, initial reset, internal interrupt, external interrupt or return from subroutine, the PC manipulates the program transfer by loading the address corresponding to each instruction. The conditional skip is activated by instruction. Once the condition is met, the next instruction, fetched during the current instruction execution, is discarded and a dummy cycle replaces it to get the proper instruction. Otherwise proceed with the next instruction. The lower byte of the program counter (PCL) is a readable and writeable register (06H). Moving data into the PCL performs a short jump. The destination will be within 256 locations. Once a control transfer takes place, an additional dummy cycle is required. Program memory - ROM The program memory is used to store the program instructions which are to be executed. It also contains data, table, and interrupt entries, and is organized with 307216 bits, addressed by the program counter and table pointer.
T1 S y s te m C lo c k
T2
T3
T4
T1
T2
T3
T4
T1
T2
T3
T4
O S C 2 ( R C o n ly ) ( N M O S o p e n d r a in o u tp u t) PC PC PC+1 PC+2
. e tc h IN S T (P C ) E x e c u te IN S T (P C -1 )
. e tc h IN S T (P C + 1 ) E x e c u te IN S T (P C )
. e tc h IN S T (P C + 2 ) E x e c u te IN S T (P C + 1 )
Execution flow
Mode Initial reset External interrupt Timer counter overflow Skip Loading PCL Jump, call branch Return from subroutine Note: *11~*0: Program counter bits #11~#0: Instruction code bits
Program Counter *11 0 0 0 *11 #11 S11 *10 0 0 0 *10 #10 S10 *9 0 0 0 *9 #9 S9 *8 0 0 0 *8 #8 S8 *7 0 0 0 @7 #7 S7 *6 0 0 0 PC+2 @6 #6 S6 @5 #5 S5 @4 #4 S4 @3 #3 S3 @2 #2 S2 @1 #1 S1 @0 #0 S0 *5 0 0 0 *4 0 0 0 *3 0 0 1 *2 0 1 0 *1 0 0 0 *0 0 0 0
S11~S0: Stack register bits @7~@0: PCL bits
Rev. 1.10
5
November 14, 2001
HT82K68E
000H 008H D e v ic e in itia liz a tio n p r o g r a m T im e r /e v e n t c o u n te r in te r r u p t s u b r o u tin e
n00H n..H
L o o k - u p ta b le ( 2 5 6 w o r d s )
P ro g ra m ROM
B..H
L o o k - u p ta b le ( 2 5 6 w o r d s ) 1 6 b its N o te : n ra n g e s fro m 0 to B
Program memory Certain locations in the program memory are reserved for special usage:
* Location 000
The TBLH is read only and cannot be restored. If the main routine and the ISR (Interrupt Service Routine) both employ the table read instruction, the contents of the TBLH in the main routine are likely to be changed by the table read instruction used in the ISR. Errors can occur. In other words, using the table read instruction in the main routine and the ISR simultaneously should be avoided. However, if the table read instruction has to be applied in both the main routine and the ISR, the interrupt is supposed to be disabled prior to the table read instruction. It will not be enabled until the TBLH has been backed up. The table pointer (TBLP) is a read/write register (07H), which indicates the table location. Before accessing the table, the location must be placed in TBLP. All table related instructions need 2 cycles to complete the operation. These areas may function as normal program memory depending upon the requirements. Stack register - STACK This is a special part of the memory which is used to save the contents of the program counter (PC) only. The stack is organized into six levels and is neither part of the data nor part of the program space, and is neither readable nor writeable. The activated level is indexed by the stack pointer (SP) and is neither readable nor writeable. At a subroutine call or interrupt acknowledgement, the contents of the program counter are pushed onto the stack. At the end of a subroutine or an interrupt routine, signaled by a return instruction (RET or RETI), the program counter is restored to its previous value from the stack. After a chip reset, the SP will point to the top of the stack. Data memory - RAM The data memory is designed with 184 8 bits. It is divided into two functional groups: special function registers and general purpose data memory (1608). Most of them are read/write, but some are read only. The special function registers include the Indirect Addressing register 0 (00H), the Memory Pointer register 0 (MP0;01H), the Indirect Addressing register 1 (02H), the Memory Pointer register 1 (MP1;03H), the Accumulator (ACC;05H), the Program Counter Lower-byte register (PCL;06H), the Table Pointer (TBLP;07H), the Table Higher-order byte register (TBLH;08H), the Watchdog Timer option Setting register (WDTS;09H), the Status register (STATUS;0AH), the Interrupt Control register Table Location *7 @7 @7 *6 @6 @6 *5 @5 @5 *4 @4 @4 *3 @3 @3 *2 @2 @2 *1 @1 @1 *0 @0 @0
This area is reserved for the initialization program. After chip reset, the program always begins execution at location 000H.
* Location 004H
Location 004H is reserved for external interrupt service program. If the PC2 (external input pin) is activated, the interrupt is enabled, and the stack is not full, the program begins execution at location 004H. The pin PE0 determine whether the rising or falling edge of the PC2 to activate external interrupt service program.
* Location 008H
This area is reserved for the timer counter interrupt service program. If timer interrupt results from a timer counter overflow, and if the interrupt is enabled and the stack is not full, the program begins execution at location 008H.
* Table location
Any location in the ROM space can be used as look-up tables. The instructions TABRDC [m] (the current page, one page=256 words) and TABRDL [m] (the last page) transfer the contents of the lower-order byte to the specified data memory, and the higher-order byte to TBLH (08H). Only the destination of the lower-order byte in the table is well-defined, the other bits of the table word are transferred to the lower portion of TBLH, the remaining 1 bit is read as 0. The Table Higher-order byte register (TBLH) is read only.
Instruction(s) TABRDC [m] TABRDL [m]
*11 P11 1
*10 P10 0
*9 P9 1
*8 P8 1
Note: *11~*0: Table location bits @7~@0: Table location bits Rev. 1.10 6
P11~P8: Current program counter bits
November 14, 2001
HT82K68E
00H 01H 02H 03H 04H 05H 06H 07H 08H 09H 0AH 0BH 0CH 0DH 0EH 0.H 10H 11H 12H 13H 14H 15H 16H 17H 18H 19H 1AH 1BH 1CH 1DH 1EH 1.H 20H 60H G e n e ra l P u rp o s e DATA M EM ORY (1 6 0 B y te s ) ..H PA PAC PB PBC PC PCC PD PDC PE PEC :U nused. R e a d a s 0 0 TM R TM RC S p e c ia l P u r p o s e DATA M EM ORY ACC PCL TBLP TBLH W DTS STATUS IN T C In d ir e c t A d d r e s s in g R e g is te r 0 MP0 In d ir e c t A d d r e s s in g R e g is te r 1 MP1
eration of [00H] and [02H] can access the data memory pointed to by MP0 (01H) and MP1 (03H) respectively. Reading location 00H or 02H indirectly will return the result 00H. Writing indirectly results in no operation. The function of data movement between two indirect addressing registers is not supported. The memory pointer registers, MP0 and MP1, are 8-bit registers which can be used to access the data memory by combining corresponding indirect addressing registers. Accumulator The accumulator is closely related to the ALU operations. It is also mapped to location 05H of the data memory and is capable of carrying out immediate data operations. The data movement between two data memory locations must pass through the accumulator. Arithmetic and logic unit - ALU This circuit performs 8-bit arithmetic and logic operation. The ALU provides the following functions:
* Arithmetic operations (ADD, ADC, SUB,
SBC, DAA)
* Logic operations (AND, OR, XOR, CPL) * Rotation (RL, RR, RLC, RRC) * Increment and Decrement (INC, DEC) * Branch decision (SZ, SNZ, SIZ, SDZ ....)
The ALU not only saves the results of a data operation but also changes the status register. Status register - Status The 8-bit status register (0AH) contains the zero flag (Z), carry flag (C), auxiliary carry flag (AC), overflow flag (OV), power down flag (PD) and watch dog time-out flag (TO). The status register not only records the status information but also controls the operation sequence. With the exception of the TO and PD flags, bits in the status register can be altered by instructions like most other registers. Any data written into the status register will not change the TO or PD flags. It should be noted that operations related to the status register may give different results from those intended. The TO and PD flags can only be changed by system power up, Watchdog Timer overflow, executing the HALT instruction and clearing the Watchdog Timer. The Z, OV, AC and C flags generally reflect the status of the latest operations. In addition, on entering an interrupt sequence or executing a subroutine call, the status register will not be automatically pushed onto the stack. If the contents of status are important and if the subroutine can corrupt the status register, precaution must be taken to save it properly.
RAM mapping (INTC;0BH), the timer counter register (TMR;0DH), the timer counter control register (TMRC;0EH), the I/O registers (PA;12H, PB;14H, PC;16H, PD;18H, PE;1AH) and the I/O control registers (PAC;13H, PBC;15H, PCC;17H, PDC;19H, PEC;1BH). The remaining space before the 60H is reserved for future expanded usage and reading these locations will get the result 00H. The general purpose data memory, addressed from 60H to FFH, is used for data and control information under instruction command. All data memory areas can handle arithmetic, logic, increment, decrement and rotate operations directly. Except for some dedicated bits, each bit in the data memory can be set and reset by the SET [m].i and CLR [m].i instructions, respectively. They are also indirectly accessible through Memory pointer registers (MP0;01H, MP1;03H). Indirect addressing register Location 00H and 02H are indirect addressing registers that are not physically implemented. Any read/write op-
Rev. 1.10
7
November 14, 2001
HT82K68E
Labels C Bits 0 Function C is set if an operation results in a carry during an addition operation or if a borrow does not take place during a subtraction operation; otherwise C is cleared. C is also affected by a rotate through carry instruction. AC is set if an operation results in a carry out of the low nibbles in addition or if no borrow from the high nibble into the low nibble in subtraction; otherwise AC is cleared. Z is set if the result of an arithmetic or logical operation is zero; otherwise Z is cleared. OV is set if an operation results in a carry into the highest-order bit but not a carry out of the highest-order bit, or vice versa; otherwise OV is cleared. PD is cleared when either a system power-up or executing the CLR WDT instruction. PD is set by executing a HALT instruction. TO is cleared by a system power-up or executing the CLR WDT or HALT instruction. TO is set by a WDT time-out. Unused bit, read as 0 Unused bit, read as 0 Status register
AC Z OV PD TO 3/4 3/4
1 2 3 4 5 6 7
Interrupt The HT82K68E provides an internal timer counter interrupt and an external interrupt shared with PC2. The interrupt control register (INTC;0BH) contains the interrupt control bits to set not only the enable/disable status but also the interrupt request flags. Once an interrupt subroutine is serviced, all other interrupts will be blocked (by clearing the EMI bit). This scheme may prevent any further interrupt nesting. Other interrupt requests may occur during this interval but only the interrupt request flag is recorded. If a certain interrupt requires servicing within the service routine, the EMI bit and the corresponding bit of the INTC may be set to allow interrupt nesting. If the stack is full, the interrupt request will not be acknowledged, even if the related interrupt is enabled, until the SP is decremented. If immediate service is desired, the stack must be prevented from becoming full. All these kinds of interrupt have the wake-up capability. As an interrupt is serviced, a control transfer occurs by pushing the program counter onto the stack followed by a branch to a subroutine at the specified location in the program memory. Only the program counter is pushed Register Bit No. 0 1 2 INTC (0BH) 3 4 5 6 7 Label EMI EEI ET0I 3/4 EIF T0F 3/4 3/4
onto the stack. If the contents of the register and Status register (STATUS) are altered by the interrupt service program which corrupt the desired control sequence, the contents should be saved in advance. The internal timer counter interrupt is initialized by setting the timer counter interrupt request flag (T0F; bit 5 of INTC), which is normally caused by a timer counter overflow. When the interrupt is enabled, and the stack is not full and the T0F bit is set, a subroutine call to location 08H will occur. The related interrupt request flag (T0F) will be reset and the EMI bit cleared to disable further interrupts. The external interrupt is shared with PC2. The external interrupt is activated, the related interrupt request flag (EIF; bit4 of INTC) is then set. When the interrupt is enabled, the stack is not full, and the external interrupt is active, a subroutine call to location 04H will occur. The interrupt request flag (EIF) and EMI bits will also be cleared to disable other interrupts. The external interrupt (PC2) can be triggered by a high to low transition, or a low to high transition of the PC2, which is depend on the output level of the PE0. When PE0 is output high, the external interrupt is triggered by Function
Controls the master (global) interrupt (1= enabled; 0= disabled) Control the external interrupt Controls the timer counter interrupt (1= enabled; 0= disabled) Unused bit, read as 0 External interrupt flag Internal timer counter request flag (1= active; 0= inactive) Unused bit, read as 0 Unused bit, read as 0 INTC register
Rev. 1.10
8
November 14, 2001
HT82K68E
a low to high transition of the PC2. When PE0 is output low, the external interrupt is triggered by a high to low transition of PC2. During the execution of an interrupt subroutine, other interrupt acknowledgements are held until the RETI instruction is executed or the EMI bit and the related interrupt control bit are set to 1 (if the stack is not full). To return from the interrupt subroutine, a RET or RETI instruction may be invoked. RETI will set the EMI bit to enable an interrupt service, but RET will not. Interrupts occurring in the interval between the rising edges of two consecutive T2 pulses, will be serviced on the latter of the two T2 pulses, if the corresponding interrupts are enabled. In the case of simultaneous requests, the following table shows the priority that is applied. These can be masked by resetting the EMI bit. No. a b Interrupt Source External interrupt 1 Timer counter overflow Vector 04H 08H nal provides the system clock. The HALT mode stops the system oscillator and resists the external signal to conserve power.
VDD
OSC1
OSC1
OSC2
fSYS/4 (NMOS Open Drain Output)
OSC2
Crystal Oscillator
RC Oscillator
System oscillator
The timer counter interrupt request flag (T0F), external interrupt request (EIF) enable timer counter bit (ET0I), enable external interrupt bit (EEI) and enable master interrupt bit (EMI) constitute an interrupt control register (INTC) which is located at 0BH in the data memory. EMI, ET0I and EEI, are used to control the enabling/disabling of interrupts. These bits prevent the requested interrupt from being serviced. Once the interrupt request flags (T0F) are set, they will remain in the INTC register until the interrupts are serviced or cleared by a software instruction. It is suggested that a program does not use the CALL subroutine within the interrupt subroutine. Because interrupts often occur in an unpredictable manner or need to be serviced immediately in some applications, if only one stack is left and enabling the interrupt is not well controlled, once the CALL subroutine operates in the interrupt subroutine it will damage the original control sequence. Oscillator configuration There are two oscillator circuits in HT82K68E. Both are designed for system clocks; the RC oscillator and the Crystal oscillator, which are determined by mask options. No matter what oscillator type is selected, the sigS y s te m c lo c k /4 M ask O p tio n S e le c t
If an RC oscillator is used, an external resistor between OSC1 and VDD is needed and the resistance must range from 51kW to 1MW. The system clock, divided by 4, is available on OSC2, which can be used to synchronize external logic. The RC oscillator provides the most cost effective solution. However, the frequency of the oscillation may vary with VDD, temperature and the chip itself due to process variations. It is, therefore, not suitable for timing sensitive operations where accurate oscillator frequency is desired. If the Crystal oscillator is used, a crystal across OSC1 and OSC2 is needed to provide the feedback and phase shift needed for oscillator, no other external components are needed. Instead of a crystal, the resonator can also be connected between OSC1 and OSC2 to get a frequency reference, but two external capacitors in OSC1 and OSC2 are required. The WDT oscillator is a free running on-chip RC oscillator, and no external components are required. Even if the system enters the power down mode, the system clock is stopped, but the WDT oscillator still works for a period of approximately 78 ms. The WDT oscillator can be disabled by mask option to conserve power. Watchdog Timer - WDT The WDT clock source is implemented by a dedicated RC oscillator (WDT oscillator) or instruction clock (system clock divided by 4), decided by mask options. This timer is designed to prevent a software malfunction or
W D T P r e s c a le r 8 - b it C o u n te r 7 - b it C o u n te r
W DT OSC
8 -to -1 M U X W D T T im e - o u t
W S0~W S2
Watchdog Timer
Rev. 1.10
9
November 14, 2001
HT82K68E
sequence jumping to an unknown location with unpredictable results. The Watchdog Timer can be disabled by mask option. If the Watchdog Timer is disabled, all the executions related to the WDT results in no operation. Once the internal WDT oscillator (RC oscillator normally with a period of 78ms) is selected, it is first divided by 256 (8-stages) to get the nominal time-out period of approximately 20 ms. This time-out period may vary with temperature, VDD and process variations. By invoking the WDT prescaler, longer time-out periods can be realized. Writing data to WS2, WS1, WS0 (bit 2,1,0 of the WDTS) can give different time-out periods. If WS2, WS1, WS0 are all equal to 1, the division ratio is up to 1:128, and the maximum time-out period is 2.6 seconds. If the WDT oscillator is disabled, the WDT clock may still come from the instruction clock and operate in the same manner except that in the HALT state the WDT may stop counting and lose its protecting purpose. In this situation the WDT logic can be restarted by external logic. The high nibble and bit 3 of the WDTS are reserved for user defined flags, which can be used to indicate some specified status. If the device operates in a noisy environment, using the on-chip RC oscillator (WDT OSC) is strongly recommended, since the HALT will stop the system clock. WS2 0 0 0 0 1 1 1 1 WS1 0 0 1 1 0 0 1 1 WS0 0 1 0 1 0 1 0 1 WDTS register The WDT overflow under normal operation will initialize chip reset and set the status bit TO. An overflow in the HALT mode, initializes a warm reset only when the PC and SP are reset to zero. To clear the contents of the WDT (including the WDT prescaler ), three methods are adopted; external reset (a low level to RESET), software instruction(s), or a HALT instruction. There are two types of software instructions; CLR WDT and CLR WDT1/CLR WDT2. Of these two types of instruction, only one can be active depending on the mask option CLR WDT times selection option. If the CLR WDT is selected (ie. CLR WDT times equal one), any execution of the CLR WDT instruction will clear the WDT. In case CLR WDT1 and CLR WDT2 are chosen (ie. CLRWDT times equal two), these two instructions must be executed to clear the WDT; otherwise, the WDT may reset the chip because of the time-out. Rev. 1.10 10 Division Ratio 1:1 1:2 1:4 1:8 1:16 1:32 1:64 1:128 Power down operation - HALT The HALT mode is initialized by the HALT instruction and results in the following...
* The system oscillator will turn off but the WDT oscilla-
tor keeps running (if the WDT oscillator is selected).
* The contents of the on chip RAM and registers re-
main unchanged.
* WDT and WDT prescaler will be cleared and recount
again (if the WDT clock has come from the WDT oscillator). * All I/O ports maintain their original status.
* The PD flag is set and the TO flag is cleared.
The system can leave the HALT mode by means of an external reset, interrupt, and external falling edge signal on port A and port C [0:3] or a WDT overflow. An external reset causes a device initialization and the WDT overflow performs a warm reset. Examining the TO and PD flags, the reason for chip reset can be determined. The PD flag is cleared when system power-up or executing the CLR WDT instruction and is set when the HALT instruction is executed. The TO flag is set if the WDT time-out occurs, and causes a wake-up that only resets the PC and SP, the others keep their original status. On the other hand, awakening from an external interrupt (PC2), two sequences may happen. If the interrupt is disabled or the interrupt is enabled but the stack is full, the program will resume execution at the next instruction. But if the interrupt is enabled and the stack is not full, the regular interrupt response takes place. The port A or port C [0:3] wake-up can be considered as a continuation of normal execution. Each bit in port A can be independently selected to wake up the device by mask option. Awakening from an I/O port stimulus, the program will resume execution of the next instruction. Once a wake-up event occurs, and the system clock comes from a crystal, it takes 1024 tSYS (system clock period) to resume normal operation. In other words, the HT82K68E will insert a dummy period after the wake-up. If the system clock comes from an RC oscillator, it continues operating immediately. If the wake-up results in next instruction execution, this will execute immediately after the dummy period is completed. To minimize power consumption, all I/O pins should be carefully managed before entering the HALT status. Reset There are three ways in which a reset can occur:
* RESET reset during normal operation * RESET reset during HALT * WDT time-out reset during normal operation
The WDT time-out during HALT is different from other chip reset conditions, since it can perform a warm reset that just resets the PC and SP, leaving the other circuits
November 14, 2001
HT82K68E
to remain in their original state. Some registers remain unchanged during other reset conditions. Most registers are reset to the initial condition when the reset conditions are met. By examining the PD and TO flags, the program can distinguish between different chip resets. TO 0 u 0 1 1 PD 0 u 1 u 1 RESET Conditions RESET reset during power-up RESET reset during normal operation RESET wake-up HALT WDT time-out during normal operation WDT wake-up HALT WDT Timer counter
VDD RESET S S T T im e - o u t C h ip R eset tS
ST
To guarantee that the system oscillator has started and stabilized, the SST (System Start-up Timer) provides an extra-delay of 1024 system clock pulses when the system powers up or when it awakes from the HALT state. When a system power-up occurs, the SST delay is added during the reset period. But when the reset comes from the RESET pin, the SST delay is disabled. Any wake-up from HALT will enable the SST delay. The functional unit chip reset status is shown below. PC Prescaler 000H Clear Clear. After master reset, WDT begins counting Off Input mode Points to the top of the stack
Note: u means unchanged
Input/output ports SP Timer counter
Reset timing chart
V
DD
A timer counter (TMR) is implemented in the HT82K68E. The timer counter contains an 8-bit programmable count-up counter and the clock may come from the system clock divided by 4. Using the internal instruction clock, there is only one reference time-base.
RESET
Reset circuit
H ALT W DT W DT T im e - o u t R eset
There are two registers related to the timer counter; TMR ([0DH]), TMRC ([0EH]). Two physical registers are mapped to TMR location; writing TMR makes the starting value be placed in the timer counter preload register and reading TMR gets the contents of the timer counter. The TMRC is a timer counter control register, which defines some options.
W a rm R eset
RESET SST 1 0 -s ta g e R ip p le C o u n te r P o w e r - o n D e te c tio n C o ld R eset
In the timer mode, once the timer counter starts counting, it will count from the current contents in the timer counter to FFH. Once overflow occurs, the counter is reloaded from the timer counter preload register and generates the interrupt request flag (TF; bit 5 of INTC) at the same time. To enable the counting operation, the timer ON bit (TON; bit 4 of TMRC) should be set to 1. In the case of timer counter OFF condition, writing data to the timer counter preload register will also reload that data to the timer counter. But if the timer counter is turned on, Function
OSC1
Reset configuration Label 3/4 TON 3/4 TM0 TM1 Bits 0~3 4 5 6 7 Unused bit, read as "0"
To enable/disable timer counting (0= disabled; 1= enabled) Unused bit, read as "0" 10= Timer mode (internal clock) TMRC register
Rev. 1.10
11
November 14, 2001
HT82K68E
data written to it will only be kept in the timer counter preload register. The timer counter will still operate until overflow occurs. When the timer counter (reading TMR) is read, the clock will be blocked to avoid errors. As clock blocking may results in a counting error, this must be taken into consideration by the programmer. Input/output ports There are 32 bidirectional input/output lines in the HT82K68E, labeled from PA to PE, which are mapped to the data memory of [12H], [14H], [16H], [18H] and [1AH] respectively. All these I/O ports can be used for input and output operations. For input operation, these ports are non-latching, that is, the inputs must be ready at the T2 rising edge of instruction MOV A,[m] (m=12H, 14H, 16H, 18H or 1AH). For output operation, all data is latched and remains unchanged until the output latch is rewritten. Each I/O line has its own control register (PAC, PBC, PCC, PDC, PEC) to control the input/output configuration. With this control register, CMOS output or Schmitt trigger input with or without pull-high resistor (mask option) structures can be reconfigured dynamically (i.e., on-the-fly) under software control. To function as an
D a ta B u s TM 1 TM 0 T im e r C o u n te r P r e lo a d R e g is te r R e lo a d
S y s te m
C lo c k /4
TM 1 TM 0 TON
P u ls e W id th M e a s u re m e n t M o d e C o n tro l
T im e r C o u n te r
O v e r flo w to In te rru p t
Timer counter The state of the registers is summarized in the following table: Register TMR TMRC PC MP0 MP1 ACC TBLP TBLH STATUS INTC WDTS PA PAC PB PBC PC PCC PD PDC PE PEC Note: Reset (Power On) xxxx xxxx 00-0 1--000H xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx -xxx xxxx --00 xxxx -000 0000 0000 0111 1111 1111 1111 1111 1111 1111 1111 1111 1111 1111 1111 1111 1111 1111 1111 1111 ---1 1111 ---1 1111 * stands for warm reset u stands for unchanged x stands for unknown Rev. 1.10 12 November 14, 2001 WDT Time-out RESET Reset (Normal Operation) (Normal Operation) uuuu uuuu 00-0 1--000H uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu -uuu uuuu --1u uuuu -000 0000 0000 0111 1111 1111 1111 1111 1111 1111 1111 1111 1111 1111 1111 1111 1111 1111 1111 1111 ---1 1111 ---1 1111 uuuu uuuu 00-0 1--000H uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu -uuu uuuu --uu uuuu -000 0000 0000 0111 1111 1111 1111 1111 1111 1111 1111 1111 1111 1111 1111 1111 1111 1111 1111 1111 ---1 1111 ---1 1111 RESET Reset (HALT) uuuu uuuu 00-0 1--000H uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu -uuu uuuu --01 uuuu -000 0000 0000 0111 1111 1111 1111 1111 1111 1111 1111 1111 1111 1111 1111 1111 1111 1111 1111 1111 ---1 1111 ---1 1111 WDT Time-out (HALT) uuuu uuuu uu-u u--000H* uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu -uuu uuuu --11 uuuu -uuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu ---u uuuu ---u uuuu
HT82K68E
D a ta B u s D CK S Q V W r ite C o n tr o l R e g is te r C h ip R e s e t R e a d C o n tr o l R e g is te r D Q CK S Q M R e a d I/O S y s te m W a k e -u p ( P A & P C 0 ~ P C 3 o n ly ) M a s k O p tio n U X W r ite I/O Q V
DD
DD
W eak P u ll- u p M a s k O p tio n PA0 PB0 PC0 PD0 PE0 ~PA ~PB ~PC ~PD ~PE 7 7 4 7 7
Input/output ports
input, the corresponding latch of the control register must write 1. The pull-high resistance will exhibit automatically if the pull-high option is selected. The input source(s) also depend(s) on the control register. If the control register bit is 1, input will read the pad state. If the control register bit is 0, the contents of the latches will move to the internal bus. The latter is possible in read-modify-write instruction. For output function, CMOS is the only configuration. These control registers are mapped to locations 13H, 15H, 17H, 19H and 1BH. After a chip reset, these input/output lines stay at high levels or floating (mask option). Each bit of these input/output latches can be set or cleared by the SET [m].i or CLR [m].i (m=12H, 14H, 16H, 18H or 1AH) instruction. Some instructions first input data and then follow the output operations. For example, the SET [m].i, CLR [m].i, CPL [m] and CPLA [m] instructions read the entire port states into the CPU, execute the defined operations
(bit-operation), and then write the results back to the latches or the accumulator. Each line of port A and port C [0:3] has the capability to wake-up the device. PC2 is shared with the external interrupt pin, PE2~PE4 is defined as CMOS output pins only. PE0 can determine whether the high to low transition, or the low to high transition of PC2 to activate the external subroutine, when PE0 output high, the low to high transition of PC2 to trigger the external subroutine, when PE0 output low, the high to low transition of PC2 to trigger the external subroutine. PE2~PE4 is configured as CMOS output only and is used to drive the LED. PC0, PC1 is configured as NMOS open drain output with 4.6kW pull-high resistor such that it can easy to use as DATA or CLOCK line of PS2 keyboard application.
Rev. 1.10
13
November 14, 2001
HT82K68E
ROM code option The following shows six kinds of ROM code option in the HT82K68E. All the ROM code options must be defined to ensure proper system function. No. 1 ROM Code Option OSC type selection. This option is to decide if an RC or Crystal oscillator is chosen as system clock. If the Crystal oscillator is selected, the XST (Crystal Start-up Timer) default is activated, otherwise the XST is disabled. WDT source selection. There are three types of selection: on-chip RC oscillator, instruction clock or disable the WDT. CLRWDT times selection. This option defines the way to clear the WDT by instruction. One time means that the CLR WDT instruction can clear the WDT. Two times means only if both of the CLR WDT1 and CLR WDT2 instructions have been executed, only then will the WDT be cleared. Wake-up selection. This option defines the wake-up function activity. External I/O pins (PA and PC [0:3] only) all have the capability to wake-up the chip from a HALT. Pull-high selection. This option is to decide whether the pull-high resistance is visible or not in the input mode of the I/O ports. Each bit of an I/O port can be independently selected. Special power on reset. This option defines the function will reset the chip to prevent incorrect status. If the special power on reset is enabled, the chip must not enter the HALT mode.
2
3
4 5 6
Application Circuits
RC o s c illa to r fo r m u ltip le I/O a p p lic a tio n s C r y s ta l o s c illa to r o r c e r a m ic r e s o n a to r fo r m u ltip le I/O a p p lic a tio n s
V PA PA PA PA PA PA PA PA PB PB PB PB PB PB PB PB PD PD PD PD PD PD PD PD PC PC 7 0 2 3 4 5 6 7 0 1 2 3 4 5 6 1 C0 C1 C2 C3 C4 C5 C6 C7 R0 R1 R2 R3 R4 R5 R6 R7 0 1 2 3 4 5 6 7 6 7 R8 R9 R10 R11 R12 R13 R14 R15 R16 R17 V RESET V
DD DD
V
DD
. .B .
10m
0 .1 m V
DD
VDD
. .B . R e s e rv e fo r R e s o n a to r
10m
0 .1 m
VDD
OSC1
(N M O S O p e n D r a in O u tp u t) V
fS
YS
/4
OSC1 OSC2
DD
OSC2
RESET
V
DD
DD
CAP NUM SCR CLK DATA CLK DATA
CAP NUM SCR CLK DATA CLK DATA
PA PA PA PA PA PA PA PA PB PB PB PB PB PB PB PB PD PD PD PD PD PD PD PD PC PC
0 1 2 3
C0 C1 C2 C3 4 5 6 7 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 6 7 C4 C5 C6 C7 R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 R10 R11 R12 R13 R14 R15 R16 R17
H T82K 68E
H T82K 68E
Rev. 1.10
14
November 14, 2001
HT82K68E
Instruction Set Summary
Mnemonic Arithmetic ADD A,[m] ADDM A,[m] ADD A,x ADC A,[m] ADCM A,[m] SUB A,x SUB A,[m] SUBM A,[m] SBC A,[m] SBCM A,[m] DAA [m] Add data memory to ACC Add ACC to data memory Add immediate data to ACC Add data memory to ACC with carry Add ACC to register with carry Subtract immediate data from ACC Subtract data memory from ACC Subtract data memory from ACC with result in data memory Subtract data memory from ACC with carry Subtract data memory from ACC with carry and result in data memory Decimal adjust ACC for addition with result in data memory Z,C,AC,OV Z,C,AC,OV Z,C,AC,OV Z,C,AC,OV Z,C,AC,OV Z,C,AC,OV Z,C,AC,OV Z,C,AC,OV Z,C,AC,OV Z,C,AC,OV C Description Flag Affected
Logic Operation AND A,[m] OR A,[m] XOR A,[m] ANDM A,[m] ORM A,[m] XORM A,[m] AND A,x OR A,x XOR A,x CPL [m] CPLA [m] AND data memory to ACC OR data memory to ACC Exclusive-OR data memory to ACC AND ACC to data memory OR ACC to data memory Exclusive-OR ACC to data memory AND immediate data to ACC OR immediate data to ACC Exclusive-OR immediate data to ACC Complement data memory Complement data memory with result in ACC Z Z Z Z Z Z Z Z Z Z Z
Increment & Decrement INCA [m] INC [m] DECA [m] DEC [m] Rotate RRA [m] RR [m] RRCA [m] RRC [m] RLA [m] RL [m] RLCA [m] RLC [m] Data Move MOV A,[m] MOV [m],A MOV A,x Bit Operation CLR [m].i SET [m].i Clear bit of data memory Set bit of data memory None None Move data memory to ACC Move ACC to data memory Move immediate data to ACC None None None Rotate data memory right with result in ACC Rotate data memory right Rotate data memory right through carry with result in ACC Rotate data memory right through carry Rotate data memory left with result in ACC Rotate data memory left Rotate data memory left through carry with result in ACC Rotate data memory left through carry None None C C None None C C Increment data memory with result in ACC Increment data memory Decrement data memory with result in ACC Decrement data memory Z Z Z Z
Rev. 1.10
15
November 14, 2001
HT82K68E
Mnemonic Branch JMP addr SZ [m] SZA [m] SZ [m].i SNZ [m].i SIZ [m] SDZ [m] SIZA [m] SDZA [m] CALL addr RET RET A,x RETI Table Read TABRDC [m] TABRDL [m] Miscellaneous NOP CLR [m] SET [m] CLR WDT CLR WDT1 CLR WDT2 SWAP [m] SWAPA [m] HALT No operation Clear data memory Set data memory Clear Watchdog Timer Pre-clear Watchdog Timer Pre-clear Watchdog Timer Swap nibbles of data memory Swap nibbles of data memory with result in ACC Enter power down mode m: Data memory address i: 0~7 number of bits O: Flag is affected *: Flag(s) may be affected by the execution status None None None TO,PD TO*,PD* TO*,PD* None None TO,PD Read ROM code (current page) to data memory and TBLH Read ROM code (last page) to data memory and TBLH None None Jump unconditionally Skip if data memory is zero Skip if data memory is zero with data movement to ACC Skip if bit i of data memory is zero Skip if bit i of data memory is not zero Skip if increment data memory is zero Skip if decrement data memory is zero Skip if increment data memory is zero with result in ACC Skip if decrement data memory is zero with result in ACC Subroutine call Return from subroutine Return from subroutine and load immediate data to ACC Return from interrupt None None None None None None None None None None None None None Description Flag Affected
Note: x: 8 bits immediate data A: Accumulator addr: Program memory address -: Flag is not affected
Rev. 1.10
16
November 14, 2001
HT82K68E
Instruction Definition
ADC A,[m] Description Operation Affected flag(s) TC2 3/4 ADCM A,[m] Description Operation Affected flag(s) TC2 3/4 ADD A,[m] Description Operation Affected flag(s) TC2 3/4 ADD A,x Description Operation Affected flag(s) TC2 3/4 ADDM A,[m] Description Operation Affected flag(s) TC2 3/4 TC1 3/4 TO 3/4 PD 3/4 OV O Z O AC O C O TC1 3/4 TO 3/4 PD 3/4 OV O Z O AC O C O TC1 3/4 TO 3/4 PD 3/4 OV O Z O AC O C O TC1 3/4 TO 3/4 PD 3/4 OV O Z O AC O C O TC1 3/4 TO 3/4 PD 3/4 OV O Z O AC O C O Add data memory and carry to the accumulator The contents of the specified data memory, accumulator and the carry flag are added simultaneously, leaving the result in the accumulator. ACC ACC+[m]+C
Add the accumulator and carry to data memory The contents of the specified data memory, accumulator and the carry flag are added simultaneously, leaving the result in the specified data memory. [m] ACC+[m]+C
Add data memory to the accumulator The contents of the specified data memory and the accumulator are added. The result is stored in the accumulator. ACC ACC+[m]
Add immediate data to the accumulator The contents of the accumulator and the specified data are added, leaving the result in the accumulator. ACC ACC+x
Add the accumulator to the data memory The contents of the specified data memory and the accumulator are added. The result is stored in the data memory. [m] ACC+[m]
Rev. 1.10
17
November 14, 2001
HT82K68E
AND A,[m] Description Operation Affected flag(s) TC2 3/4 AND A,x Description Operation Affected flag(s) TC2 3/4 ANDM A,[m] Description Operation Affected flag(s) TC2 3/4 CALL addr Description TC1 3/4 TO 3/4 PD 3/4 OV 3/4 Z O AC 3/4 C 3/4 TC1 3/4 TO 3/4 PD 3/4 OV 3/4 Z O AC 3/4 C 3/4 TC1 3/4 TO 3/4 PD 3/4 OV 3/4 Z O AC 3/4 C 3/4 Logical AND accumulator with data memory Data in the accumulator and the specified data memory perform a bitwise logical_AND operation. The result is stored in the accumulator. ACC ACC AND [m]
Logical AND immediate data to the accumulator Data in the accumulator and the specified data perform a bitwise logical_AND operation. The result is stored in the accumulator. ACC ACC AND x
Logical AND data memory with the accumulator Data in the specified data memory and the accumulator perform a bitwise logical_AND operation. The result is stored in the data memory. [m] ACC AND [m]
Subroutine call The instruction unconditionally calls a subroutine located at the indicated address. The program counter increments once to obtain the address of the next instruction, and pushes this onto the stack. The indicated address is then loaded. Program execution continues with the instruction at this address. Stack PC+1 PC addr
Operation Affected flag(s)
TC2 3/4 CLR [m] Description Operation Affected flag(s) TC2 3/4
TC1 3/4
TO 3/4
PD 3/4
OV 3/4
Z 3/4
AC 3/4
C 3/4
Clear data memory The contents of the specified data memory are cleared to 0. [m] 00H
TC1 3/4
TO 3/4
PD 3/4
OV 3/4
Z 3/4
AC 3/4
C 3/4
Rev. 1.10
18
November 14, 2001
HT82K68E
CLR [m].i Description Operation Affected flag(s) TC2 3/4 CLR WDT Description Operation Affected flag(s) TC2 3/4 CLR WDT1 Description TC1 3/4 TO 0 PD 0 OV 3/4 Z 3/4 AC 3/4 C 3/4 TC1 3/4 TO 3/4 PD 3/4 OV 3/4 Z 3/4 AC 3/4 C 3/4 Clear bit of data memory The bit i of the specified data memory is cleared to 0. [m].i 0
Clear Watchdog Timer The WDT and the WDT Prescaler are cleared (re-counting from 0). The power down bit (PD) and time-out bit (TO) are cleared. WDT and WDT Prescaler 00H PD and TO 0
Preclear Watchdog Timer The TO, PD flags, WDT and the WDT Prescaler has cleared (re-counting from 0), if the other preclear WDT instruction has been executed. Only execution of this instruction without the other preclear instruction just sets the indicated flag which implies this instruction has been executed and the TO and PD flags remain unchanged. WDT and WDT Prescaler 00H* PD and TO 0*
Operation Affected flag(s)
TC2 3/4 CLR WDT2 Description
TC1 3/4
TO 0*
PD 0*
OV 3/4
Z 3/4
AC 3/4
C 3/4
Preclear Watchdog Timer The TO, PD flags, WDT and the WDT Prescaler are cleared (re-counting from 0), if the other preclear WDT instruction has been executed. Only execution of this instruction without the other preclear instruction, sets the indicated flag which implies this instruction has been executed and the TO and PD flags remain unchanged. WDT and WDT Prescaler 00H* PD and TO 0*
Operation Affected flag(s)
TC2 3/4 CPL [m] Description Operation Affected flag(s) TC2 3/4
TC1 3/4
TO 0*
PD 0*
OV 3/4
Z 3/4
AC 3/4
C 3/4
Complement data memory Each bit of the specified data memory is logically complemented (1s complement). Bits which previously contained a 1 are changed to 0 and vice-versa. [m] [m]
TC1 3/4
TO 3/4
PD 3/4
OV 3/4
Z O
AC 3/4
C 3/4
Rev. 1.10
19
November 14, 2001
HT82K68E
CPLA [m] Description Complement data memory and place result in the accumulator Each bit of the specified data memory is logically complemented (1s complement). Bits which previously contained a 1 are changed to 0 and vice-versa. The complemented result is stored in the accumulator and the contents of the data memory remain unchanged. ACC [m]
Operation Affected flag(s)
TC2 3/4 DAA [m] Description
TC1 3/4
TO 3/4
PD 3/4
OV 3/4
Z O
AC 3/4
C 3/4
Decimal-Adjust accumulator for addition The accumulator value is adjusted to the BCD (Binary Coded Decimal) code. The accumulator is divided into two nibbles. Each nibble is adjusted to the BCD code and an internal carry (AC1) will be done if the low nibble of the accumulator is greater than 9. The BCD adjustment is done by adding 6 to the original value if the original value is greater than 9 or a carry (AC or C) is set; otherwise the original value remains unchanged. The result is stored in the data memory and only the carry flag (C) may be affected. If ACC.3~ACC.0 >9 or AC=1 then [m].3~[m].0 (ACC.3~ACC.0)+6, AC1=AC else [m].3~[m].0) (ACC.3~ACC.0), AC1=0 and If ACC.7~ACC.4+AC1 >9 or C=1 then [m].7~[m].4 ACC.7~ACC.4+6+AC1,C=1 else [m].7~[m].4 ACC.7~ACC.4+AC1,C=C
Operation
Affected flag(s) TC2 3/4 DEC [m] Description Operation Affected flag(s) TC2 3/4 DECA [m] Description Operation Affected flag(s) TC2 3/4 TC1 3/4 TO 3/4 PD 3/4 OV 3/4 Z O AC 3/4 C 3/4 TC1 3/4 TO 3/4 PD 3/4 OV 3/4 Z O AC 3/4 C 3/4 TC1 3/4 TO 3/4 PD 3/4 OV 3/4 Z 3/4 AC 3/4 C O
Decrement data memory Data in the specified data memory is decremented by 1. [m] [m]-1
Decrement data memory and place result in the accumulator Data in the specified data memory is decremented by 1, leaving the result in the accumulator. The contents of the data memory remain unchanged. ACC [m]-1
Rev. 1.10
20
November 14, 2001
HT82K68E
HALT Description Enter power down mode This instruction stops program execution and turns off the system clock. The contents of the RAM and registers are retained. The WDT and prescaler are cleared. The power down bit (PD) is set and the WDT time-out bit (TO) is cleared. PC PC+1 PD 1 TO 0
Operation
Affected flag(s) TC2 3/4 INC [m] Description Operation Affected flag(s) TC2 3/4 INCA [m] Description Operation Affected flag(s) TC2 3/4 JMP addr Description Operation Affected flag(s) TC2 3/4 MOV A,[m] Description Operation Affected flag(s) TC2 3/4 TC1 3/4 TO 3/4 PD 3/4 OV 3/4 Z 3/4 AC 3/4 C 3/4 TC1 3/4 TO 3/4 PD 3/4 OV 3/4 Z 3/4 AC 3/4 C 3/4 TC1 3/4 TO 3/4 PD 3/4 OV 3/4 Z O AC 3/4 C 3/4 TC1 3/4 TO 3/4 PD 3/4 OV 3/4 Z O AC 3/4 C 3/4 TC1 3/4 TO 0 PD 1 OV 3/4 Z 3/4 AC 3/4 C 3/4
Increment data memory Data in the specified data memory is incremented by 1 [m] [m]+1
Increment data memory and place result in the accumulator Data in the specified data memory is incremented by 1, leaving the result in the accumulator. The contents of the data memory remain unchanged. [m]+1
Directly jump Bits of the program counter are replaced with the directly-specified address unconditionally, and control is passed to this destination. PC addr
Move data memory to the accumulator The contents of the specified data memory are copied to the accumulator. ACC [m]
Rev. 1.10
21
November 14, 2001
HT82K68E
MOV A,x Description Operation Affected flag(s) TC2 3/4 MOV [m],A Description Operation Affected flag(s) TC2 3/4 NOP Description Operation Affected flag(s) TC2 3/4 OR A,[m] Description Operation Affected flag(s) TC2 3/4 OR A,x Description Operation Affected flag(s) TC2 3/4 ORM A,[m] Description Operation Affected flag(s) TC2 3/4 TC1 3/4 TO 3/4 PD 3/4 OV 3/4 Z O AC 3/4 C 3/4 TC1 3/4 TO 3/4 PD 3/4 OV 3/4 Z O AC 3/4 C 3/4 TC1 3/4 TO 3/4 PD 3/4 OV 3/4 Z O AC 3/4 C 3/4 TC1 3/4 TO 3/4 PD 3/4 OV 3/4 Z 3/4 AC 3/4 C 3/4 TC1 3/4 TO 3/4 PD 3/4 OV 3/4 Z 3/4 AC 3/4 C 3/4 TC1 3/4 TO 3/4 PD 3/4 OV 3/4 Z 3/4 AC 3/4 C 3/4 Move immediate data to the accumulator The 8-bit data specified by the code is loaded into the accumulator. ACC x
Move the accumulator to data memory The contents of the accumulator are copied to the specified data memory (one of the data memories). [m] ACC
No operation No operation is performed. Execution continues with the next instruction. PC PC+1
Logical OR accumulator with data memory Data in the accumulator and the specified data memory (one of the data memories) perform a bitwise logical_OR operation. The result is stored in the accumulator. ACC ACC OR [m]
Logical OR immediate data to the accumulator Data in the accumulator and the specified data perform a bitwise logical_OR operation. The result is stored in the accumulator. ACC ACC OR x
Logical OR data memory with the accumulator Data in the data memory (one of the data memories) and the accumulator perform a bitwise logical_OR operation. The result is stored in the data memory. [m] ACC OR [m]
Rev. 1.10
22
November 14, 2001
HT82K68E
RET Description Operation Affected flag(s) TC2 3/4 RET A,x Description Operation Affected flag(s) TC2 3/4 RETI Description Operation Affected flag(s) TC2 3/4 RL [m] Description Operation Affected flag(s) TC2 3/4 RLA [m] Description Operation Affected flag(s) TC2 3/4 TC1 3/4 TO 3/4 PD 3/4 OV 3/4 Z 3/4 AC 3/4 C 3/4 TC1 3/4 TO 3/4 PD 3/4 OV 3/4 Z 3/4 AC 3/4 C 3/4 TC1 3/4 TO 3/4 PD 3/4 OV 3/4 Z 3/4 AC 3/4 C 3/4 TC1 3/4 TO 3/4 PD 3/4 OV 3/4 Z 3/4 AC 3/4 C 3/4 TC1 3/4 TO 3/4 PD 3/4 OV 3/4 Z 3/4 AC 3/4 C 3/4 Return from subroutine The program counter is restored from the stack. This is a 2-cycle instruction. PC Stack
Return and place immediate data in the accumulator The program counter is restored from the stack and the accumulator loaded with the specified 8-bit immediate data. PC Stack ACC x
Return from interrupt The program counter is restored from the stack, and interrupts are enabled by setting the EMI bit. EMI is the enable master (global) interrupt bit (bit 0; register INTC). PC Stack EMI 1
Rotate data memory left The contents of the specified data memory are rotated 1 bit left with bit 7 rotated into bit 0. [m].(i+1) [m].i; [m].i:bit i of the data memory (i=0~6) [m].0 [m].7
Rotate data memory left and place result in the accumulator Data in the specified data memory is rotated 1 bit left with bit 7 rotated into bit 0, leaving the rotated result in the accumulator. The contents of the data memory remain unchanged. ACC.(i+1) [m].i; [m].i:bit i of the data memory (i=0~6) ACC.0 [m].7
Rev. 1.10
23
November 14, 2001
HT82K68E
RLC [m] Description Operation Rotate data memory left through carry The contents of the specified data memory and the carry flag are rotated 1 bit left. Bit 7 replaces the carry bit; the original carry flag is rotated into the bit 0 position. [m].(i+1) [m].i; [m].i:bit i of the data memory (i=0~6) [m].0 C C [m].7
Affected flag(s) TC2 3/4 RLCA [m] Description TC1 3/4 TO 3/4 PD 3/4 OV 3/4 Z 3/4 AC 3/4 C O
Rotate left through carry and place result in the accumulator Data in the specified data memory and the carry flag are rotated 1 bit left. Bit 7 replaces the carry bit and the original carry flag is rotated into bit 0 position. The rotated result is stored in the accumulator but the contents of the data memory remain unchanged. ACC.(i+1) [m].i; [m].i:bit i of the data memory (i=0~6) ACC.0 C C [m].7
Operation
Affected flag(s) TC2 3/4 RR [m] Description Operation Affected flag(s) TC2 3/4 RRA [m] Description Operation Affected flag(s) TC2 3/4 RRC [m] Description Operation TC1 3/4 TO 3/4 PD 3/4 OV 3/4 Z 3/4 AC 3/4 C 3/4 TC1 3/4 TO 3/4 PD 3/4 OV 3/4 Z 3/4 AC 3/4 C 3/4 TC1 3/4 TO 3/4 PD 3/4 OV 3/4 Z 3/4 AC 3/4 C O
Rotate data memory right The contents of the specified data memory are rotated 1 bit right with bit 0 rotated to bit 7. [m].i [m].(i+1); [m].i:bit i of the data memory (i=0~6) [m].7 [m].0
Rotate right and place result in the accumulator Data in the specified data memory is rotated 1 bit right with bit 0 rotated into bit 7, leaving the rotated result in the accumulator. The contents of the data memory remain unchanged. ACC.(i) [m].(i+1); [m].i:bit i of the data memory (i=0~6) ACC.7 [m].0
Rotate data memory right through carry The contents of the specified data memory and the carry flag are together rotated 1 bit right. Bit 0 replaces the carry bit; the original carry flag is rotated into the bit 7 position. [m].i [m].(i+1); [m].i:bit i of the data memory (i=0~6) [m].7 C C [m].0
Affected flag(s) TC2 3/4 Rev. 1.10 TC1 3/4 TO 3/4 PD 3/4 24 OV 3/4 Z 3/4 AC 3/4 C O November 14, 2001
HT82K68E
RRCA [m] Description Rotate right through carry and place result in the accumulator Data of the specified data memory and the carry flag are rotated 1 bit right. Bit 0 replaces the carry bit and the original carry flag is rotated into the bit 7 position. The rotated result is stored in the accumulator. The contents of the data memory remain unchanged. ACC.i [m].(i+1); [m].i:bit i of the data memory (i=0~6) ACC.7 C C [m].0
Operation
Affected flag(s) TC2 3/4 SBC A,[m] Description Operation Affected flag(s) TC2 3/4 SBCM A,[m] Description Operation Affected flag(s) TC2 3/4 SDZ [m] Description TC1 3/4 TO 3/4 PD 3/4 OV O Z O AC O C O TC1 3/4 TO 3/4 PD 3/4 OV O Z O AC O C O TC1 3/4 TO 3/4 PD 3/4 OV 3/4 Z 3/4 AC 3/4 C O
Subtract data memory and carry from the accumulator The contents of the specified data memory and the complement of the carry flag are subtracted from the accumulator, leaving the result in the accumulator. ACC ACC+[m]+C
Subtract data memory and carry from the accumulator The contents of the specified data memory and the complement of the carry flag are subtracted from the accumulator, leaving the result in the data memory. [m] ACC+[m]+C
Skip if decrement data memory is 0 The contents of the specified data memory are decremented by 1. If the result is 0, the next instruction is skipped. If the result is 0, the following instruction, fetched during the current instruction execution, is discarded and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle). Skip if ([m]-1)=0, [m] ([m]-1)
Operation Affected flag(s)
TC2 3/4 SDZA [m] Description
TC1 3/4
TO 3/4
PD 3/4
OV 3/4
Z 3/4
AC 3/4
C 3/4
Decrement data memory and place result in ACC, skip if 0 The contents of the specified data memory are decremented by 1. If the result is 0, the next instruction is skipped. The result is stored in the accumulator but the data memory remains unchanged. If the result is 0, the following instruction, fetched during the current instruction execution, is discarded and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle). Skip if ([m]-1)=0, ACC ([m]-1)
Operation Affected flag(s)
TC2 3/4
TC1 3/4
TO 3/4
PD 3/4
OV 3/4
Z 3/4
AC 3/4
C 3/4
Rev. 1.10
25
November 14, 2001
HT82K68E
SET [m] Description Operation Affected flag(s) TC2 3/4 SET [m]. i Description Operation Affected flag(s) TC2 3/4 SIZ [m] Description TC1 3/4 TO 3/4 PD 3/4 OV 3/4 Z 3/4 AC 3/4 C 3/4 TC1 3/4 TO 3/4 PD 3/4 OV 3/4 Z 3/4 AC 3/4 C 3/4 Set data memory Each bit of the specified data memory is set to 1. [m] FFH
Set bit of data memory Bit i of the specified data memory is set to 1. [m].i 1
Skip if increment data memory is 0 The contents of the specified data memory are incremented by 1. If the result is 0, the following instruction, fetched during the current instruction execution, is discarded and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle). Skip if ([m]+1)=0, [m] ([m]+1)
Operation Affected flag(s)
TC2 3/4 SIZA [m] Description
TC1 3/4
TO 3/4
PD 3/4
OV 3/4
Z 3/4
AC 3/4
C 3/4
Increment data memory and place result in ACC, skip if 0 The contents of the specified data memory are incremented by 1. If the result is 0, the next instruction is skipped and the result is stored in the accumulator. The data memory remains unchanged. If the result is 0, the following instruction, fetched during the current instruction execution, is discarded and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle). Skip if ([m]+1)=0, ACC ([m]+1)
Operation Affected flag(s)
TC2 3/4 SNZ [m].i Description
TC1 3/4
TO 3/4
PD 3/4
OV 3/4
Z 3/4
AC 3/4
C 3/4
Skip if bit i of the data memory is not 0 If bit i of the specified data memory is not 0, the next instruction is skipped. If bit i of the data memory is not 0, the following instruction, fetched during the current instruction execution, is discarded and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle). Skip if [m].i0
Operation Affected flag(s)
TC2 3/4
TC1 3/4
TO 3/4
PD 3/4
OV 3/4
Z 3/4
AC 3/4
C 3/4
Rev. 1.10
26
November 14, 2001
HT82K68E
SUB A,[m] Description Operation Affected flag(s) TC2 3/4 SUBM A,[m] Description Operation Affected flag(s) TC2 3/4 SUB A,x Description Operation Affected flag(s) TC2 3/4 SWAP [m] Description Operation Affected flag(s) TC2 3/4 SWAPA [m] Description Operation Affected flag(s) TC2 3/4 TC1 3/4 TO 3/4 PD 3/4 OV 3/4 Z 3/4 AC 3/4 C 3/4 TC1 3/4 TO 3/4 PD 3/4 OV 3/4 Z 3/4 AC 3/4 C 3/4 TC1 3/4 TO 3/4 PD 3/4 OV O Z O AC O C O TC1 3/4 TO 3/4 PD 3/4 OV O Z O AC O C O TC1 3/4 TO 3/4 PD 3/4 OV O Z O AC O C O Subtract data memory from the accumulator The specified data memory is subtracted from the contents of the accumulator, leaving the result in the accumulator. ACC ACC+[m]+1
Subtract data memory from the accumulator The specified data memory is subtracted from the contents of the accumulator, leaving the result in the data memory. [m] ACC+[m]+1
Subtract immediate data from the accumulator The immediate data specified by the code is subtracted from the contents of the accumulator, leaving the result in the accumulator. ACC ACC+x+1
Swap nibbles within the data memory The low-order and high-order nibbles of the specified data memory (1 of the data memories) are interchanged. [m].3~[m].0 [m].7~[m].4
Swap data memory and place result in the accumulator The low-order and high-order nibbles of the specified data memory are interchanged, writing the result to the accumulator. The contents of the data memory remain unchanged. ACC.3~ACC.0 [m].7~[m].4 ACC.7~ACC.4 [m].3~[m].0
Rev. 1.10
27
November 14, 2001
HT82K68E
SZ [m] Description Skip if data memory is 0 If the contents of the specified data memory are 0, the following instruction, fetched during the current instruction execution, is discarded and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle). Skip if [m]=0
Operation Affected flag(s)
TC2 3/4 SZA [m] Description
TC1 3/4
TO 3/4
PD 3/4
OV 3/4
Z 3/4
AC 3/4
C 3/4
Move data memory to ACC, skip if 0 The contents of the specified data memory are copied to the accumulator. If the contents is 0, the following instruction, fetched during the current instruction execution, is discarded and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle). Skip if [m]=0
Operation Affected flag(s)
TC2 3/4 SZ [m].i Description
TC1 3/4
TO 3/4
PD 3/4
OV 3/4
Z 3/4
AC 3/4
C 3/4
Skip if bit i of the data memory is 0 If bit i of the specified data memory is 0, the following instruction, fetched during the current instruction execution, is discarded and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle). Skip if [m].i=0
Operation Affected flag(s)
TC2 3/4 TABRDC [m] Description Operation Affected flag(s) TC2 3/4 TABRDL [m] Description Operation Affected flag(s) TC2 3/4
TC1 3/4
TO 3/4
PD 3/4
OV 3/4
Z 3/4
AC 3/4
C 3/4
Move the ROM code (current page) to TBLH and data memory The low byte of ROM code (current page) addressed by the table pointer (TBLP) is moved to the specified data memory and the high byte transferred to TBLH directly. [m] ROM code (low byte) TBLH ROM code (high byte)
TC1 3/4
TO 3/4
PD 3/4
OV 3/4
Z 3/4
AC 3/4
C 3/4
Move the ROM code (last page) to TBLH and data memory The low byte of ROM code (last page) addressed by the table pointer (TBLP) is moved to the data memory and the high byte transferred to TBLH directly. [m] ROM code (low byte) TBLH ROM code (high byte)
TC1 3/4
TO 3/4
PD 3/4
OV 3/4
Z 3/4
AC 3/4
C 3/4
Rev. 1.10
28
November 14, 2001
HT82K68E
XOR A,[m] Description Operation Affected flag(s) TC2 3/4 XORM A,[m] Description Operation Affected flag(s) TC2 3/4 XOR A,x Description Operation Affected flag(s) TC2 3/4 TC1 3/4 TO 3/4 PD 3/4 OV 3/4 Z O AC 3/4 C 3/4 TC1 3/4 TO 3/4 PD 3/4 OV 3/4 Z O AC 3/4 C 3/4 TC1 3/4 TO 3/4 PD 3/4 OV 3/4 Z O AC 3/4 C 3/4 Logical XOR accumulator with data memory Data in the accumulator and the indicated data memory perform a bitwise logical Exclusive_OR operation and the result is stored in the accumulator. ACC ACC XOR [m]
Logical XOR data memory with the accumulator Data in the indicated data memory and the accumulator perform a bitwise logical Exclusive_OR operation. The result is stored in the data memory. The 0 flag is affected. [m] ACC XOR [m]
Logical XOR immediate data to the accumulator Data in the accumulator and the specified data perform a bitwise logical Exclusive_OR operation. The result is stored in the accumulator. The 0 flag is affected. ACC ACC XOR x
Rev. 1.10
29
November 14, 2001
HT82K68E
Holtek Semiconductor Inc. (Headquarters) No.3, Creation Rd. II, Science-based Industrial Park, Hsinchu, Taiwan Tel: 886-3-563-1999 Fax: 886-3-563-1189 http://www.holtek.com.tw Holtek Semiconductor Inc. (Sales Office) 11F, No.576, Sec.7 Chung Hsiao E. Rd., Taipei, Taiwan Tel: 886-2-2782-9635 Fax: 886-2-2782-9636 Fax: 886-2-2782-7128 (International sales hotline) Holtek Semiconductor (Shanghai) Inc. 7th Floor, Building 2, No.889, Yi Shan Rd., Shanghai, China Tel: 021-6485-5560 Fax: 021-6485-0313 http://www.holtek.com.cn Holtek Semiconductor (Hong Kong) Ltd. RM.711, Tower 2, Cheung Sha Wan Plaza, 833 Cheung Sha Wan Rd., Kowloon, Hong Kong Tel: 852-2-745-8288 Fax: 852-2-742-8657 Holmate Semiconductor, Inc. 48531 Warm Springs Boulevard, Suite 413, Fremont, CA 94539 Tel: 510-252-9880 Fax: 510-252-9885 http://www.holmate.com Copyright O 2001 by HOLTEK SEMICONDUCTOR INC. The information appearing in this Data Sheet is believed to be accurate at the time of publication. However, Holtek assumes no responsibility arising from the use of the specifications described. The applications mentioned herein are used solely for the purpose of illustration and Holtek makes no warranty or representation that such applications will be suitable without further modification, nor recommends the use of its products for application that may present a risk to human life due to malfunction or otherwise. Holtek reserves the right to alter its products without prior notification. For the most up-to-date information, please visit our web site at http://www.holtek.com.tw.
Rev. 1.10
30
November 14, 2001

▲Up To Search▲

Price & Availability of HT82K68E07

	To Download HT82K68E07 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .